How to Rescue Your Mobile Phone from a Swim

by Gadget Grave
Water damage in cell phones is a very common issue. Often people drop their phone in the sink, leave it in the pocket while washing the clothes or drop it into their pet’s water bowl. It is a surprising fact that it is not the water damage but the actions the user takes after taking the device out of water that makes the phone irreparable. If you take the right steps at this time, you can save your phone from the damage. Here is how to handle your device before you visit a cell phone repair specialist:Take your device out of water as soon as possible – The layout of mobile phones always has certain tiny holes in it like the charging port, microphone port, speaker aperture and other ports. These holes allow water seepage into the device. So it is advised to remove the device from the fluid as soon as possible. If your device is connected to the wall charger and submerged in water at the same time, never try to grab it before you turn off the charger as it can result into an electric shock.

Dismantle the device – If the phone is still powered on, turn it off immediately. Remove the back cover, battery, SIM card, memory card and other cell phone accessories from the device. Get some towels and blotting paper to dry the water droplets that are still there inside the device. Certain devices have indicators on them to help the user determine if any kind of damage has occurred. To determine the damage sign for your device, read its manual and find out if the water damage has occurred or your device has somehow survived.

Dry out every drop of water from the device – If possible, you can try placing the device under the sun or in open air to dry. Make sure the phone screen is not facing the sunlight. Try cleaning your phone with cotton soaked in alcohol to displace the remaining water droplets. A vacuum cleaner can also be used to suck out the liquid. Hold the vacuum cleaner at a safe distance from the device as vacuum can create static electricity spoiling the phone further. Silica gel, salt or rice are excellent water absorbents that can also be used to draw out the remaining moisture.

Never use a hair dryer – Instead of drying the device out, a hair dryer can push the droplets in further. The impurities in water can cause the device to corrode and result into permanent damage. Also, very hot air can melt some of the components or connections inside the device.

Wait before you turn on the device – You may be sure of your device being completely dry but it is highly recommended to wait for at least 24 hours before you turn on your device after drying it completely. If the device is not working or malfunctioning, you must visit a cell phone repair specialist to get it fixed. If your device is completely dry, it will be of great helpyou’re your cell phone repair specialist. There are certain cell phone accessories available in the market that can save your device from such damage.

Cole is a provider of efficient and cost effective cell phone repair services in Arkansas. The company also provides a huge range of cell phone accessories for different makes and models. For more information, visit Gadget Grave.

View more articles from Gadget Grave
This article is provided by Amazines.com – The ULTIMATE Article Database

What to Look for in Refurbished Networking Equipment

By

If you are looking for a way to cut the cost for your company there are many approaches you might take. You may reduce overtime hours, opt for a lower priced cleaning service or swap to more energy efficient lights. However, is another option that you might overlook, that can actually save a significant amount of money. This budget saving option is to choose refurbished networking equipment rather than buying new.

Today, there are many companies out there who are taking used networking equipment and refurbishing it so that it can be used for many more years. No longer must you always buy brand new equipment for your computer network. Now, you can spend less and still do more. Whether you are looking for switches, routers, gateways or servers there are many companies who have learned how to take these elements of networking equipment, give them an update and repair (if needed) and then make them available to consumers at a reduced cost. “But,” you may ask, “How does one ensure that refurbished networking equipment is the answer?” No worries. Here are some consideration to keep in mind if you are trying to determine if refurbished networking equipment is the answer for your business.

· What type of warranty does the refurbished networking equipment come with? If the company is not willing to provide you with a warranty then it means they are not very convinced of the parts performance/capabilities. Choose a refurbishing company that is will to provide an extended warranty.

· Does their network hardware have a reliability rating that they stand behind? If the vendor refuses to take a stand and tell you how often their equipment works correctly versus incorrectly, then either they are poor record keepers or they know the numbers but don’t want to share the information.

· What type of network hardware replacement program do they offer to their customers? If they refurbished networking equipment provider is not willing to offer replacements for any parts that may not work, then find another provider. As the buyer, you need to know that the part is going to work and that if it doesn’t they are going to back it and replace it. Again, failure to do this is an indication that the company does not believe in the quality of their work.

· Is their cost comparable to other companies you have considered working with? Be wary of any company that is significantly below the market. Lowest price is not necessarily the best decision.

· Are their parts checked out by a third party source? This shows that the company is willing to have someone else check their work and is willing to share that review. This indicates a desire to meet high quality standards, which means you come out ahead.

Buying refurbished networking equipment is a great way to save money and still advance your company’s business. Should you be looking for a vendor for refurbished equipment, you might wish to consider Source One Computers in Twin Cities, MN. With a little bit of patience and due diligence, you can soon save your company money and still get the parts and pieces you need.

Many websites provide additional information on the topic of networking equipment. One such site worth visiting is http://www.s1computer.com

Janet Slagell independently authors articles for WebDrafter.com, Inc. for search engine marketing. The views and opinions expressed in this article are those solely of the author, and not of any other person, company or organization. No guarantee or warranty, express or implied, is made regarding the accuracy, fitness, or use of the content herein.

Article Source: http://EzineArticles.com/?expert=Janet_Slagell

New Tech: Made In Space is the first in-space manufacturing company.

This video explains the core vision behind the company as told by its leaders from their headquarters in Moffett Field, CA (in order of appearance):

Aaron Kemmer – Chief Executive Officer, Co-founder
Mike Snyder – Lead Engineer, Head of R&D
Mike Chen – Chief Strategy Officer, Co-founder
Jason Dunn – Chief Technology Officer, Co-founder

—-About Made In Space—-
Founded in 2010 with the goal of enabling humanity’s future in space, Made In Space, Inc. has developed additive manufacturing technology for use in zero-gravity. By constructing hardware that can build what is needed in space, as opposed to launching it from Earth, the company plans to accelerate and broaden space development while also providing unprecedented access for people on Earth to use in-space capabilities.

Made In Space’s team consists of successful entrepreneurs, experienced space experts and key 3D printing developers. With over 30,000+ hours of 3D printing technology testing, and 400+ parabolas of microgravity test flights, Made In Space’s experience and expertise has led to the first 3D printers designed for use on the International Space Station.

—-About the Zero Gravity 3D Printer—-
Made in Space’s Zero-G Printer is the first 3D printer designed to operate in zero gravity. It is currently scheduled to launch to the International Space Station on September 19th, 2014 under a joint partnership between NASA MSFC and Made in Space. Contracted as the “3D Printing in Zero-G Experiment,” this first version of the Zero-G printer will begin the era of off-world manufacturing.

This initial version of the Zero-G Printer will serve as a test bed for understanding the long-term effects of microgravity on 3D printing, and how it can enable the future of space exploration. It is a culmination of contracts and development dating back to 2010 including microgravity tests with NASA’s Flight Opportunities Program, R&D contracts under NASA’s SBIR Programs, and development contracts with NASA MSFC.

Video Credit: NASA
Music Credit: DJ Roman LaCosta – Discovery New World
Music Credit: John Murphy – Sunshine (Adagio In D Minor)
itunes.apple.com/us/album/sunshine-music­­-from-motion/id297702863

Network Printer Is Printing Slow – A Simple Solution

By

Is your Sharp network printer slow when printing from your computer? Does it print one page, stop, then print another, and then stop? These are problems that occur on a daily basis in busy offices. Don’t bother calling your tech group until you’ve tried these simple solutions yourself.

Let’s speed that printer up! Here are a few tips that will likely get your network printer to print at its advertised speed!

Before you begin it’s a good idea to have a control test print that you know how long it takes the printer to output.

1. Cycle power to the printer. Just a simple reboot can help sort out any quirks the printer is having. Turn it off or unplug it, leave it off or unplugged for a minute or two, then fire it back up and test it out. If this tip doesn’t help then move on to the next step.

2. Bypass any unnecessary network equipment.

A connectivity issue normally causes slow printing. Make sure that the network cable (Cat5) is not running through a power surge protector, a 5-port switch/hub, or any other sort of network device. Ideally it should be plugged directly into the router, or into a designated network wall jack for the copier. 5-port switches are very touchy, and sometimes the individual ports will “go bad.” Try to bypass the switch if at all possible. If you only have one network drop for 2 or more devices, I recommend having a network drop ran specifically for the Sharp printer. Also, make sure the cat5 cable itself is intact and doesn’t have any flat spots, exposed or frayed wires. If it is a homemade cable it may have some issues.

3. Adjust the bitmap compression in the Sharp print driver.

The Sharp print driver also has an adjustable option that will improve printing speed, especially with larger color documents. We have found that changing the bitmap compression from Very High Quality to medium quality cuts down significantly on spooling size and print output time with virtually no quality loss. This setting can be defaulted in the print driver.

1. Open your control panel, then go to the printers menu

2. Right click on the Sharp and click Printing Preferences

3. Go to the advanced tab, and change the Bitmap Compression to medium quality, click apply then OK.

If your printer isn’t a Sharp search around in the print driver settings for “bitmap compression” or “compression,” adjust the settings, then send a test print. Don’t make any changes if you don’t know where to revert back to the previous settings!

If these adjustments do not help with your printing speed then contact your local servicing vendor for more assistance.

With over 10 years experience in the copier business Copier Collin can help with a variety of different printing issues, or provide a quote on new office equipment. Remember the name Collin Grimes the next time you need a new copier or printer for your company.

Article Source: http://EzineArticles.com/?expert=Collin_Grimes

What Is RFID?

By

RFID or Radio Frequency Identification is the wireless use of magnetic fields to transfer data, as it automatically identifies tracking tags that have been placed on or in objects. What is a tracking tag you may ask? Well, a tag is a small device that can be placed on things so that they can be followed through production–as in the auto industry for example, or on items that are ready to be shipped or moved–as in a clothing store for instance. They can also be used in livestock, pets and yes, even people, although tracking people has its own set of consequences and problems associated with it.

Micro chipping your new puppy is the perfect example of how RFID works. Your pet receives a tiny (about the size of a grain of rice) tag that is delivered via an injection and sits right under their skin. If they are ever lost, RFID technology can get them back to their rightful owner simply by reading the tag and garnering the required information that is stored in it.

To be read, a tag must contain information and you must use a reader to get that information. Some tags are read only which means they contain information as simple as just a factory assigned serial number or information that is more complex, such as stock numbers, batch numbers, production date or any number of other things that will be used to keep track of the items they are affixed to. Tags that are read/write allows the user to use specific data specially designed for their needs depending on their business protocols.

A RFID reader then sends an encoded radio signal to interact with a tag, the tag gets the message and responds with its identification. Readers can read hundreds of tags at the same time which allows warehouses and huge automobile plants to run that much more smoothly, with the people always knowing where certain parts are at any time of the day or night.

RFID readers and tags can be used in virtually any environment and in any temperature range so they are useful in a wide variety of applications. Anything from automated paying for parking or for using pay as you go on toll roads and bridges can be controlled through radio frequency identification, allowing the user ease of access, convenience and efficiency as they go about their daily lives.

GAO RFID offers one of the world’s largest selections of RFID devices, software and solutions and has over 20 years experience delivering these products to customers worldwide. Please feel free to visit http://www.gaorfid.com to find out more.

Article Source: http://EzineArticles.com/?expert=Amanda_J_Hales

Secure Data Destruction: 4 Ways To Destroy A Hard Drive

Article by By  

Are you looking for ways on how to destroy your hard drive? Here are some of them:

Burning

While heat won’t destroy data it will aid in turning your platters into liquid piles. There are a number of ways on how to burn the device. One of the ways is by using fire. This can be in the fireplace or hobo barrel. All you need to do is to toss the device in the fire and then leave it there for some time.

Another way is by using a blow torch. Here you need to put on some protective gear, hold the platter at distance and watch it melt.

If you are an adventurous hard drive destroyer, you can use a thermite. You should fill a large container with sand and then place the platter on the sand. You should then light a container of thermite over the platter. This technique produces a lot of heat that destroys the hard drive.

You can also use sugar and saltpeter. You should mix sugar and saltpeter in a soda can and place it over the hard disk.

While burning will destroy the device, you should be careful. For example, you should avoid doing the technique indoors as it tends to produce fumes that are harmful. The technique is also dangerous because sometimes there are explosions that can be harmful.

Hammering

This is the probably the fastest and most direct way of destroying the platter. You need to place the hard drive on a hard surface and then hit it with a hammer. You should ensure that you wear protective gear. For example, you should wear goggles and safety gloves.

You should also ensure that you are the only person in the room. This is to avoid hurting anyone with flying bits of glass and metal.

Magnetizing

You need to use giant magnets. If you have money you can buy the magnets; however, if you don’t have money you should take your drive to a local junk or scrap yard. The good side with this technique is that it not only aids in destroying the drive, but it also ensures that all the data is erased.

Shredding

There are many industries with shredders that you can use and all you need to do is to rent some time with it and destroy your drive. There are also some companies that have shredders that are specifically designed to destroy hard drives. All you need to do is to visit these companies and ask them to destroy the device on your behalf.

We provide secure data destruction services that ensure that your data is safe and can’t be accessed by anyone. One of the best services we provide is hard drive shredding services. To know more visit our website now.

Article Source: http://EzineArticles.com/?expert=Alex_Maccoll

Article Source: http://EzineArticles.com/8804201

How To Fix a Printer Paper Jam

How To Fix a Printer Paper Jam

One of the most frequent problems people face when it comes to printers are paper jams. A paper jam is when, for whatever reason, the paper becomes jammed in the printer and nothing can be printed. Paper jams can halt your printing completely. Often, a paper jam is easily fixed without damaging your printer in any way.

Here are some steps to follow when fixing a printer paper jam as well as some tips to avoid any future problems.

1. Turn off your printer

It’s simple really, as soon as you see there is a problem with your printer, switch it off. This stops the printer damaging itself or you whilst you are trying to fix it.

2. Locate the problem

Open the lid of the printer and have a look around. You’ll be able to see where the paper has become crumpled and jammed. Also look for an opening at the rear of the printer. You should be able to get a clear view and locate the source of the problem.

3. Remove the paper

The best way to remove a trapped sheet of paper is to firstly take out all the paper in the tray that is not caught in the jam. Then slowly and gently remove the jammed sheet, pulling it in the direction that your printer prints in.

4. Avoid ripping the paper

If you pull too hard on a trapped sheet of paper and it rips, this could damage your printer. If the paper does rip, try rotating the roller to free up the sheet. Do not try to force it out with a screwdriver as this can cause even more damage to the printer.

5. Turn on your printer again

Once you have taken out all the trapped paper and avoided any rips, you can close the printer’s lids and turn the device back on again. Perform a test print to see if your printer is working correctly. If there are still bits trapped in, just repeat the relevant steps to free it.

If your printer is still not functioning and is reporting a problem, then you should contact your printer’s manufacturer for further help.

Tips to avoid another paper jam:

– Paper jams are usually caused by the same problem: too many sheets in the paper tray.

– Don’t overload how much paper you put in to make it easier for the paper to stay aligned and print free from jamming.

– Don’t mix paper types when you print.

Avoiding paper jams in your printer is just one way of making your ink cartridges last longer which saves you money in the long run. For more helpful tips on how to save money with your printer, click here.

Article Source: http://EzineArticles.com/?expert=James_T_Graves